Going to Build

Hi Everyone,
Well, it was a lovely day today--there are birds chirping like crazy and the squirrels are running all over the place. I took advantage and went down to the wood shop and did a little work this afternoon:

I had a large piece of Phillipine mahogany left over from some other projects and decided to turn it into a platter and it came out really well:


Its a large shallow serving platter. It needs more sanding so thats on tap for later today or tomorrow.

I also hollowed out the large hickory bowl:

This is going to be a large bowl when its done. It has a lovely deep pink color and there is some spalting on the wood as well. This goes into the drying bag shortly.


And last of all, I have the mother of all wood chip piles in my shop at the moment:


I wonder how high this will get before it falls over?

Time to stop and make dinner (I wish someone would make me dinner) and get cleaned up. Im beginning to look like the wood chip pile!

More later,

VW

Fitting the Panels and Cutting Rabbet for the Glass















These last few days Ive been busy with the door project; with the main frame essentially complete I focused on the four door panels. These are solid Oak about 1 1/8" thick and needed to be rabbeted on all four sides to slide into the 1/2" door dados. The dados were cut about 1/4" deeper than needed to allow the panels to expand and contract as all solid wood will do over time. A straight forward procedure that first establishes the width and depth of the panel rabbets with my marking gauge and then starting the cut with my skew rabbet plane by Veritas. Ive read a few reviews of this plane and it seems like most have been good but to be frank, I still cant seem to find a rhythm with it. Maybe its just me but this plane never quite lived up to expectations. After using it for a year or more now I still seem to get inconsistent results.? Perhaps its the angled front knob that throws me off or the uncomfortable side profile while in use...could be the knobs that hold the fence in position have come loose on me a few times while in use and I find when I really tighten the little turn screws down to keep things tightly in place, I need a pair of pliers to get them open again.? anyone else have any thoughts on this plane? Whatever the reasons are its not my favourite plane to use for the entire process of cutting rabbets. (as a side note I should say that my small plough and large router planes by Veritas are great tools that I use daily; just seems the skew block has some issues-at least in my hands!)
So with that in mind I begin the rabbet with the Veritas and once a shallow groove is established Ill switch over to my medium sized shoulder plane to finish off the cuts. I get better results with this approach and clean things up with my side rabbet planes to complete. Again I apologise, no shots of these last few steps...been so busy trying to get this project done that the camera is sometimes an after thought! Sorry...
With the panels cut and fit Ill lay out the larger rabbets around the window section. This is basically the same procedure as the last and I did remember to turn on the camera.
To begin, a nice deep scribe line with the marking gauge on the back of the door.

With the rabbet widths and depths nicely scribed into the Oak Ill go ahead and dis-assemble things to begin the process. Again its a combination of the skew rabbet plane to start, followed by my shoulder plane. These are all stopped rabbets so each end of the channel needs to be cut with my large router plane. I work my way down through the fiber until I reach my desired depth. This procedure is generally the same for the four components but after I did the first two I started to remove the waste with a little more gusto. In the photos you may notice a large Japanese style chisel on my bench top; for removing this waste in a hurry I resorted to the bash and crash of the 1 3/8" wide steel and my heavy mallet.

















Once the bulk of the material is removed I clean up the bottom and sides of the groove with again the shoulder plane and router to get tight into the corners...
another dry fit to check and I can move on.






















I follow these same steps and complete the other three rabbets getting a little more aggressive with the mallet and chisel as I go; these rabbets are big and deep and in this small work space the simple task of taking a style, cutting a rabbet, fitting the rail and then taking it apart and fine tuning things is a real workout. As the door gets closer to completion my shop is feeling smaller and smaller. I can safely say that this is the first and the last door Ill attempt to build in this workspace.
From here its on to some more hand planing but my spirits are lifted because Im very happy with the results so far. This planing session should be one of the last and my smoothing plane is taking paper shavings off of the stock. Another dry fit and I can start to get set-up for the mouldings...
















Hallelujah!

When I made covered buttons for the headboard, I decided to use the aqua tray for a hard surface while assembling the buttons, bad idea ... it broke on the very first button. So this week I finally got around to fixing it!



I found paper at World Market on clearance for $1.98, and decided to paint the red with liquid gold leaf



I love the super glossy finish! Have you used resin on anything recently?